How To Repair A Broken Fishing Rod
We alive in the age of a "simply buy a new one" mentality, just that doesn't mean it's the all-time way to go. Fixing a rod yourself is much cheaper and more rewarding than just tossing it in the trash.
Fishing rod repair is quite easy, and you lot can set but about anything on your rod with fiddling knowledge or experience.
How to Repair a Broken Fishing Rod
So, you've broken the essential tool in your arsenal. (Okay, maybe the reel is the vital tool…)
Unless you accept the onetime rod out of the garage and fire it back up, you lot'll be out of commission for a while. Why not effort and fix information technology yourself?
ane. Gather Everything Together
In that location are a few things you will need to repair your broken angling rod properly:
- 15-minute epoxy
- An old rod similar in size that y'all no longer use
- Ii-part blanket like Flexcoat
- Rod winding thread
Make sure you fix aside a good corporeality of fourth dimension and but tackle this chore if y'all know you accept enough time to meet it through. When you are epoxying the rod, you don't desire to take to go up and walk abroad, because that would injure your event.
2. Identify the Amercement
Now that you have everything together and you are ready to start working, take a look at the suspension to determine what your action plan volition be. Where exactly is the intermission? If the fissure is right on the blank and not near whatsoever guides, that will brand the process easier because you won't have to remove anything to get the job done.
You as well need to determine what kind of break it is. If the break is clean and smooth, information technology volition be easier to manage because y'all won't demand that long of an insert to take the force per unit area off the blank.
If the broken part is crushed or shattered it'll but require a much longer insert and more attention with the epoxy.
3. Prepare Your Insert
The first thing you want to do is measure the broken piece of rod. Y'all want to determine how long of an insert you need to create with the onetime rod. The goal is to have at least six inches of the insert on both sides of the broken rod.
Sand down the damaged sections of the rod until they are smoothen so you lot tin get an accurate measurement. Put the two broken sections together and measure half-dozen inches out on both sides to make up one's mind how much of an insert you need. If the inserting rod is slightly likewise big, the two pieces will not sit down flush upwards against each other, so go along that in mind when measuring too.
Use a slice of the blank that is slightly smaller than the expanse you are inserting it and put it in to test it. If the inserting portion moves more than a fiddling flake, and so y'all need to increase the size of the blank piece.
four. Epoxy The Two Pieces Together
Once you lot take everything ready, so information technology all fits together nicely, at present you tin epoxy the two pieces together. Coat the insert generously in the epoxy and start sliding it into one section of the broken rod. Push it in until it covers the entire cleaved role, and so slide the other one-half of the cleaved rod over the insert until it's thoroughly flush with the bottom piece.
Clean up any backlog epoxy from exterior the break and set the rod up vertically, then make sure the epoxy rests accordingly. Do not motility the rod for at to the lowest degree two hours.
Remember to clean everything well earlier the epoxy sets, considering information technology's quite a mess to make clean it later.
5. Wrapping The Area
So at present you accept waited two hours or longer, and everything looks practiced. Now yous can wrap the area with the rod thread. You want to wrap information technology as tightly as possible holding the thread taut throughout the entire procedure and wrap four inches out from the break on both sides.
At that place are many unlike sizes of thread, and they range from 'A' to 'Eastward.' There is no right or wrong on what you can use here, we recommend using something in the middle—as long equally you can pull information technology overnice and tight without breaking.
6. Apply The Flexcoat
Once your rod is wrapped upwardly, get alee and apply the Flexcoat while you lot are turning the rod. If yous have a rotisserie that is the ideal situation but even if someone stands and rotates the rod for you while you lot apply the coat, that is fine too.
Comprehend the unabridged wrapped area nicely with the Flexcoat and proceed turning it for a few minutes even afterwards you are washed applying to brand certain there are no runs. If at that place are some slight runs it'southward okay, because the rod volition still take the necessary strength it needs to perform—it just might not look as polish.
At this indicate, your rod should exist good equally new. (if not better) You're ready to striking the water over again!
Angling Rod Guide Repair
Your guides are an incredibly important function of the rod. They help y'all properly cast and pull dorsum without your line getting tangled and out of club. If you are missing fifty-fifty one guide, it could cause you to have too much drag, resulting in snapped lines and lost fish.
Luckily, fixing a guide is simple.
Guides are usually held on with epoxy, so all you take to do is rut the broken guide with a lighter or candle to break the seal.
Once the guide gets squeamish and hot, you should see it starting to break away from the blank and then you tin cut information technology off with a bract. Just exist conscientious not to cut or harm the blank—it might be soft from the heat also.
Subsequently you lot have completely removed the guide, clean the expanse with booze to remove whatever old epoxy or grime that was beneath the seal.
Take your new guide and use a thin thread wrap—this should be the thinnest wrap you tin can employ.
Wrap the thread around the guide and the rod tightly and seal the new guide onto the bare using a glaze of epoxy. Let this set for at least two hours earlier moving the rod, and give it 24 hours before you take the rod out on the water.
If there is any backlog epoxy, use rough dust sandpaper to take information technology off.
Fishing Rod Tip Repair
If you've broken the tip of your rod, you tin't build an insert like yous would for the rod blank, you have to gum it back on using a ferrule. A ferrule is a slice that goes over the top to bring together two pieces together, like a bandage.
Offset, you desire to cutting the tip with large scissors or clippers to brand sure you have a overnice make clean break and sand downward the edge, so it sits nicely against the new tip.
Put some hot glue inside the ferrule of the new tip and slide information technology over the sanded broken expanse. Make sure there is enough mucilage that information technology's dripping out from the broken area. This creates an fantabulous seal, and you tin can wipe off whatever excess afterward.
Hold the two pieces in place until the glue sets and store the rod vertically, so it dries appropriately.
One time everything is dry, sand off whatever excess glue.
Fishing Rod Handle Repair
Fixing the handle of your rod in the outcome of breakage is very simple. This can be done quickly and easily using the supplies we have already talked discussed.
If the handle is cork, sand it downwards until it's shine and drill a hole in each section. Have a pocket-size wooden dowel and insert it into the cork. Coat the dowel with hot glue and insert it into the blank side of the handle.
Take the new section and slide it over the dowel leaving near an 8th of an inch open. Coat the opening with glue and push the ii pieces together creating an excellent seal.
Wipe off any leftover gum and let it sit for a few hours before moving. Sand off any excess once its dry.
It'south frustrating—and even scary—when y'all break your rod or any of its components, but don't panic.
Follow these uncomplicated steps if you are dealing with breakage, and you'll exist dorsum out on the water in no fourth dimension.
Source: https://blog.overtons.com/fishing/fishing-rod-repair-read-this-before-you-throw-it-away
0 Response to "How To Repair A Broken Fishing Rod"
Post a Comment